As an example: some people might be using the offerings from Microsoft or Amazon, whilst other people might be running a VM with a VPS somewhere and hosting their apps like Homeassistant, OpenHAB, Node-Red etc there.

I wanted to know if you do something like this, and what might be the downsides to doing something like this.

Thanks!

  • Moonrise2473@feddit.it
    link
    fedilink
    arrow-up
    5
    arrow-down
    1
    ·
    1 year ago

    Home assistant is already a mess to properly configure in the lan where the auto discovery does most of the job, doing it in the cloud under a VPN (because you don’t plan to expose the iot devices to the internet, right?) Increases the complexity for no benefit

      • λλλ
        link
        fedilink
        arrow-up
        3
        ·
        1 year ago

        Good luck connecting all of your IoT devices to the tailnet though. You’ll need a firewall and lots of tinkering. I use linode and host some stuff in the cloud, but not Home Assistant.

        • MigratingtoLemmy@lemmy.worldOP
          link
          fedilink
          arrow-up
          2
          ·
          1 year ago

          What do you mean? Isn’t this supposed to work similar to a direct VPN connection to the VPS box, i.e. akin to the machine being in the same network? Am I missing something? What do you mean by “firewall” (on my side, or on the side of the VPS)?

          I’ll likely be using Node-red and MQTT with some automation apps, probably. Not decided yet.

          • λλλ
            link
            fedilink
            arrow-up
            2
            ·
            edit-2
            1 year ago

            Tailnet requires you to run the Tailscale client. I would bet that the Tailscale client isn’t even built to run on some/all of your IoT devices. Even if it were, I doubt many little esp devices would have the overhead to run them.

              • λλλ
                link
                fedilink
                arrow-up
                3
                arrow-down
                1
                ·
                1 year ago

                It just might. That’s what I meant by firewall btw. A router is usually just three things, a firewall, a network switch, and a wireless access point. The part that handles routing to the internet (and your cloud instance) will be the firewall. I have OPNSense as my firewall with Tailscale installed on it.

      • chaospatterns@lemmy.world
        link
        fedilink
        English
        arrow-up
        2
        ·
        1 year ago

        Tailnet appears to be Tailscale which is Wireguard underneath. This means it operates at layer 3 (IP). However a bunch of smart home stuff (mDNS, WoL, etc) all depend on layer 2 connectivity (same subnet).

        That means some stuff won’t work correctly.

        • MigratingtoLemmy@lemmy.worldOP
          link
          fedilink
          arrow-up
          1
          ·
          1 year ago

          I see. Could you give me a few more examples on what could break if I go forward with this? Will I still need to consider multicast DNS if my DNS server is on-prem (Pi-Hole + Unbound)?

          I remember that it was not possible to route multicast traffic through IPSec earlier, which is why people used to opt for GRE-over-IPSec. But just as IPSec supports multicast traffic now, doesn’t Wireguard too? Or am I missing something important as to why this is not supported?

          • chaospatterns@lemmy.world
            link
            fedilink
            English
            arrow-up
            1
            ·
            1 year ago

            Will I still need to consider multicast DNS if my DNS server is on-prem (Pi-Hole + Unbound)

            Multicast DNS is separate from DNS, so even if you have Pi-Hole, you’d still have devices using mDNS. It’s possible to route mDNS across separate IP networks seeing as how there’s mDNS relays across VLANs which would suggest Wireguard could support Multicast. Other things use Broadcast (e.g. WoL) which is a bit more challenging to forward across IP networks.

            I’m not familiar with GRE so I couldn’t comment on whether it’s possible or not. I guess it all depends on how confident you are with your networking skills. If you get it working, you should definitely document it and share with others.

            I didn’t quite do what you did, but I ran HA in a Kubernetes cluster which was logically a separate IP network. I had to setup the container with multiple network interfaces and specially craft the route table to forward broadcasts + multicast traffic to the correct network.

            • MigratingtoLemmy@lemmy.worldOP
              link
              fedilink
              arrow-up
              1
              ·
              1 year ago

              Thank you for your reply.

              It seems I need to study mDNS more. I haven’t had the opportunity to play with IOT much, but this is something I never considered.

              I will not be working with GRE over Wireguard though, I’d like to keep it simpler.

              Thanks again, I’ll have a look. Thanks for the tip with k8s