Ahoy hoy!
I have a new build I’m tryin to cobble together but I can’t get it to post the first time.
I have a ASRock B650E Taichi M/B, Ryzen 7 7600x cpu, an EVGA 850w Gold, a MSI 2060, 32 gig of ram, 1tb SSD and a 1000gig HDD, all in a Fractal Torrent case. I’ve hooked everything up and can see the RGB and smart switches light up, but when I hit either power button I get no response.
I’ve reseated the cables, removed the GPU, reseated the ram, waited hours, and nothin, not even the fans kickin up. What Am I missin?
Update: sorry for the delay, works been crazy. The PSU has a tester so I was able to confirm the fans an PSU works. Unhooked everything and plugged it back in, same results.
Update 2: Electric Boogaloo: success! Thank you for all the help, culprit was either the power supply itself or the cables, but the fix was a new psu
I had something like this once, in that case it was front io connected to wrong pins on motherboard.
Reseated them again and made sure they were all facing the same way now, per the book, and still nothin
Had the same exact issue - upgrade BIOS. You need to download from ASRock, write to USB, and follow instructions using the button on motherboard since no display.
And I have to do that for first post?
edit: you waited hours, nevermind. But fyi-
Is it doing the ddr5 training?
https://hardforum.com/threads/long-boot-time-for-am5-normal.2034383/
Your board has a debugging code at the bottom, do they light up?
If they do, you can find the number in the manual
If they don’t light up, then I’d assume the board isn’t getting power, try removing the mobo from the case and check if you’ve got any case standoffs in places where they’d touch the mobo.
Your CPU has integrated graphics, so while the motherboard’s out try testing it with just the CPU, RAM and PSU.
If it still doesn’t work you might have to try using a different mobo / try and get an RMA on your current.
No code, which is maddening. I can hear the backup power supply I’m plugged into trying to turn on when I hit power the first time, and the RGB on the board itself as well as the smart switches light up
Did you try taking the mobo out the case and testing it, the CPU and RAM? If you did and it’s still not working, then I’d follow u/dcdc’s advice and update the bios, the board could be on an early build that doesn’t support your RAM.
Here’s a link to updating your BIOS without posting.
And the latest (non beta) BIOS link.
make sure you have a cable directly from monitor to the motherboard/GPU if you installed one already. Don’t go through a dock as some docks need firmware drivers, that could be the cause of failure.
Straight into the board an no dock
On the off chance your front io buttons are broken, try bridging the contacts with a screwdriver?
Also, you may want to test your PSU by bridging the green wire to black, on the large 20 pin connector (disconnect first to be safe)
The board has a power button on it as well that also doesn’t respond, the RGB and buttons on the board light up though nothin
Pretty unlikely that the board button and the case button are both broken, you may have a brick on your hands.
Worth testing the PSU anyway, in case only one of the voltages is broken. But you’ll need a multimeter.
Are you sure you used the right number of standoffs underneigth? No shorts or anything?
There are 9 in the case, all at the eatx spots with the one in the center having a raised point to act as a guide for the rest
Have you tried a minimal build? Mobo, CPU, 1 stick of ram, nothing else?
Try a couple of the ram sticks, but only one at a time?
I still suspect you have a dead mono, but its worth a try in case something else is causing a short or something.
