A Qnap NAS has a drive with some bad sectors, I want to RMA it, but before just want to figure out how to prepare a drive? It’s part of a raid 5 setup of 4 drives unencrypted. So I want to remove it and wipe it. Got a Linux machine I can use, but never done this before.
What are common Linux tools to do that sensibly?
You must log in or register to comment.
shredCan also be used from KDE Partition Manager.
Use LUKS encryption on the future.shredor alternatively you can zero out all the bytes in a drive withdd if=/dev/zero of=/dev/<DRIVE>dd if=/dev/zero of=/dev/disk
I’d recommend /dev/urandom instead of /dev/zero
Use shred , it will automate multiple random passes, and finish with a zero pass.
Completely unnecessary. Overwriting the whole drive with zeros completely stops anyone from being able to recover anything
It won’t stop “anyone”, I’ve been lead to believe there are ways even after a single pass, to recover data. if I had anything to hide, I would use a physical destruction method, nothing else
If you’re that paranoid about it, then just physically destroy the drive.
This is a miss understanding. Deleting it doesn’t actually delete the data, just the meta data. Overwrite it and it’s gone forever
Yeh, you’re right
deleted by creator
This is what I was gonna say
sudo dd if=/dev/urandom of=/dev/[sdx] bs=4096K status=progressOr for multiple passes:
sudo shred -fzv /dev/[sdx]Change [sdx] to the drive you want to wipe, make sure you double check it’s the right one.
Assuming the drive writes normally a simple command like
dd if=/dev/random of=/dev/sdX
Where sdX is the location of the drive should do the trick. Depending on drive time this may take a bit.
Yeah my first thought was just keep running dd commands, and sooner or later you’ll have the hdd wiped.
Instructions unclear, accidentally deleted 200 EB of irrecoverable NASA data.
Just keep in mind that you can’t wipe the bad sectors that have been remapped. That’s unlikely to be an issue for a personal drive, but something to consider if it held particularly sensitive information.
Always use /dev/urandom for this purposes. /dev/random will be locked if it doesn’t have enough entropy. It is good for getting some random kilobytes for cryptography but not 2 TB of random data for disk wipe.
Thanks for the heads up!
dd if=/dev/zero of=/dev/sdX bs=1M
This command is much faster. Instead of random bits, it just marks everything zero (dude). Is good enough.
no help to you, but a heads-up to anybody yet to deploy disks in such a scenario: always use encryption by way of LUKS2. you can set it up easily to unlock it on boot by a key file on the boot drive, thumb drive, TPM and such. so when a drive gets sold, RMA’d, etc., you got none of these issues.
source: sold my old drives recently and the shred procedure took ages. the new ones are encrypted so none of that shit no more.
Since dipshits are down voting me for being right, I’ll just leave this here
Thank you thats useful to know!
If the drive has bad sectors that it can’t read right now, it likely had other sectors that were marginal and got copied (remapped) to new spare sectors before they became unreadable. So there is still potentially recoverable data in the remapped sectors, and not much you can do about it.
Basically, writing zeros to the disk is about as good as you can hope for. If your data is s00per seekrit to the point where you can’t stand the possibility of any bits at all being recovered, you basically have to melt the drive. Otherwise, zero it and send it in.
Next time, set up encryption ahead of time, so your new drives never see plaintext. Some drives have a “secure erase” feature that is basically a crappy version of this built into the drive.
I like badblocks in destructive mode. It can also do multiple rounds of overwriting. It is also a good tool to burn in a new hdd or test a used one. just check smartctl bad sector count, run it, check again if it increased.
When I sold my drives, I used veracrypt with a 128 character password and PIM of 800+.
Isn’t that the same thing as shredding?
No.
Can you elaborate?
Installing an operating system and enabling encryption won’t overwrite the data on the entire disk. Instead, it will only overwrite on the specific sectors on which this operating system was installed.
Other “previous” data on the disk will remain intact and unaffected.
Unless the OS installer chooses to wipe the driver, which Debian’s (non-calamares) installer does.
I understand what you mean. The way I did it was a full disk encryption as an “external drive” so the whole disk was encrypted
DNAM. Is or used to be on the UBCD.
For the future remember, encryption helps when the disk is no longer operational.
